Metal Gates

Metal Gates: You will quite agree that there is hardly any standard gate that is not made of metal. So if you are looking for a metal related business to start. Starting this type of business is not capital intensive.

Which metal is used to make a gate: Steel Gates.
STEEL GATES – Steel is also a popular metal to fabricate gates out of, especially when a modern look is desired. For gates steel is also popular as it is stronger than wrought iron, is corrosion resistant, and is rust-proof.

How are iron gates made: Many iron gates are made from a mold; the metal is melted, placed into the mold, then is allowed to cool. This process produces “cast” iron and allows iron gates to be mass-produced, thereby driving down the cost to you. The very act of hand working iron makes the material stronger and more resistant to rust.

Which gate is better iron or steel: Wrought iron gate contains iron and small amounts of Carbon while stainless steel is made up of a standardized mixture of carbon and iron. This makes stainless steel gate more durable than wrought iron as carbon intensify the strength of steel. The advantage of containing iron is that it can resist vibration and shock.

What is cheaper wrought iron or aluminum:
Aluminum fences are typically much cheaper than their wrought iron fence counterparts, while requiring less overall maintenance. One important factor to keep in mind with aluminum fences is that they do tend to have more flex than a traditional wrought iron fence.

How do you hide metal fence posts:
Hold your wood board in front of your metal post, and determine how close to the ground you would like it to hang. Make sure it covers the top of the ugly metal fence post. The loop will hang off of the top bracket or fence line. Measure 2 ½ inches below the spot where the wire will hang off of.

Why is Aluminium better than iron:
Aluminium has some advantages over steel. Since it has a lower density than iron or steel, a car body made from aluminium will be lighter than the same car body made from steel. This results in improved fuel economy. Also, aluminium does not corrode easily because it has a protective layer of aluminium oxide.

How do you screen a gate: Position the screen panel against the inside face of the gate for the best appearance when approaching the gate. Align the bottom edge with the lower horizontal rail of the gate from end to end. Align the sides of the panel vertically and evenly spaced from the outer edges of the gate at each side.

Can Cast Iron be welded: Cast iron is difficult, but not impossible, to weld. In most cases, welding on cast iron involves repairs to castings, not joining casting to other members. The repairs may be made in the foundry where the castings are produced, or may be made to repair casting defects that are discovered after the part is machined.

Various Types of Hinges and Where to Use Them: Butt Hinge: From application ranging from doors, windows, cabinets and almost all furniture these are the most commonly used type of hinges.
Barrel Hinge, Piano Hinges, Butterfly Hinges, Flush Hinges:
Pivot Hinges, Barrel Hinge, Spring Hinge:

How do you use metal fence posts: use string and stakes to layout the desired location for your fence and dig holes for metal posts. Concrete can be used to set the posts into the ground. Use cedar, redwood or preservative-treated lumber and finish with exterior grade stain or paint. Dimensions can be modified to fit your specific needs.

Do metal fence posts need concrete:
Traditionally, chain link fences are held in place by buried posts surrounded in concrete. However, it is possible to install a chain link fence without concrete. With a hole that is the proper size, either gravel or a polymer backfill can keep fence posts in place for many years.

Is 2 feet deep enough for fence posts:
The minimum depth that you should dig your fence post holes for panel sections is 2 feet. A general formula is to dig the holes one-third to one-half of the post's aboveground height. The deeper you dig the holes, the more stability your fence has, but you must also purchase longer posts.

Metal Gates are important to houses, car sheds, godowns, stock rooms, warehouses, Function halls for entrance to protect their own goods and equipment.

Wishing you all the best,
http://www.seeyourneeds.in